المنتجات

Although this power supply design is specific to the Intelligent Power Modules (IPM), the concepts and circuit design may be used for any power supply that requires high voltage output up to 400V DC and 6 A. It is an unregulated power supply, DC output is dependent on AC input.  The circuitry includes a passive EMI filter consisting of elements C5, C6, C7, C8, C9, C10, T1, and a BR1 25 A/600V rectifier block, R3 NTC for inrush current protection, and a relay RL1 for soft powering up and reducing conduction losses in steady-state operation. 2 x electrolytic capacitors C3, C4 are used for buffering the rectified DC bus voltage. It is advisable to use a heatsink on the bridge rectifier. Inrush current circuit requires 12-15V DC @ 50mA power supply. Choose appropriate fuse as per current requirement.

This 350W power factor boost converter is designed for inverter-fed BLDC/PMSM motor appliances, A/C units, Refrigerators, and industrial power supplies. The circuit is a continuous-conduction-mode boost converter implemented using a UCC28180 PFC controller module which provides all the necessary built-in protections. It’s a robust output supply protected for output cover current, output over-voltage, and output under voltage conditions. The converter has two parts, the main power board and the UCC28180 PFC controller/Breakout board. PFC boost converter provides 380V_DC regulated output at 0.9A load current. The PFC converter accommodates an input voltage range of 85V_AC to 265 V_AC and uses average current mode control at a fixed programmable switching frequency of 120Khz.

The project presented here is a 3 Phase (3Wire) EMI Power line filter which reduces electromagnetic interference and noise conducting in to and out of equipment power lines. These EMI filters can prevent electromagnetic noise of equipment going into the power line and disturb the proper functions of other devices such as communication devices, digital circuits, and robotics thus noise generated from switched power electronics. This single-stage board is designed and built using a high-quality common mode inductor and AC capacitors.  This filter can be used to filter EMI noise in AC power lines 480VAC and can handle currents up to 10A. 3 x fuses are provided for over current and short circuit protection. It is easy to connect inputs and outputs using Barrier’s screw terminals. 6 x 4.2MM mounting holes were provided for easy mounting of the PCB.

The project presented here is a universal input AC/DC switching buck regulator with ultra-low standby power that is capable of delivering up to 2.5W output power. The RAA223012 chip is the heart of the project which combines constant off-time control for heavy load and Pulse Frequency Modulation (PFM) for light-load operation. Constant off-time controls switching frequency above the audible frequency of approximately 50kHz. PFM eliminates any potential audible noises while offering superior light-load efficiency and ultra-low power consumption (<10mW at no load). Efficiency is achieved up to 75%. The built-in frequency dithering further reduces the EMI noise spectrum.  The RAA223012 also features input brownout protection that prevents input circuitry from the overcurrent at low input voltage, and hiccup protections for output fault conditions such as short-circuit, overload, and open feedback.

This project provides 12V output from any USB power source, like PC USB port, USB adapter or power banks. LM2577ADJ boost converter IC is the heart of the project. The IC can handle load up to 800mA, it’s advisable to use only 200mA load on output to be on the safe side. The LM2577 are monolithic integrated circuits that provide all of the power and control functions for step-up (boost), fly back, and forward converter switching regulators. The device is available in three different output voltage versions: 12V, 15V, and adjustable. Requiring a minimum number of external components, these regulators are cost effective, and simple to use. Listed in this data sheet are a family of standard inductors and fly back transformers designed to work with these switching regulators. Included on the chip is a 3.0A NPN switch and its associated protection circuitry, consisting of current and thermal limiting, and under voltage lockout. Other features include a 52 kHz fixed-frequency oscillator that requires no external components, a soft start mode to reduce in-rush current during start-up, and current mode control for improved rejection of input voltage and output load transients.

This project has 2 outputs that enable us to power up 2 USB devices simultaneously from an input supply of 12-30V DC. The idea of this project is to have safe power for USB powered devices. The circuit is designed to simplify USB port power delivery based on self-powering 2 port USB HOST/HUB. IC provides two constant current outputs each of 1.1Amp 5V DC, and when any of USB port is overload/short circuit, the fault flag goes from high to low, and the outputs are in constant current mode.  The project can be used as a dual-port USB charger in cars or trucks.

The circuit shown here is a compact and high-efficiency boost converter that has been designed for hand-held equipment. This boost converter converts 2 cells (3V) DC power into 5V DC with output load current up to 500mA. Typical efficiency when boosting battery inputs is 85%. The circuit is based on MAX711 which integrates a step-up DC-DC converter with a linear regulator to provide step-up voltage conversion. The circuit is optimized for battery applications where the input varies above and below the regulated output voltage. The project has an input range from +1.8V to +11V. The circuit is set for 5V output but it has an adjustable output that can be set from +2.7V to +5.5V with the help of two R3, R4 resistors. The IC contains a comparator for low battery detection. If the voltage at LBI+ falls below that at LBI- (typically connected to REF), LBO goes low. Hysteresis is typically 50mV. You can set the low-battery monitor’s threshold with two resistors, R1 and R2.

This is a small size power supply based on OPA549 power op-amp that provides output voltage 1.2V to 25V with 0 to 10A adjustable current limit. Two onboard trimmer potentiometers provided to adjust the voltage and current, LED D1 is over temperature indicator. The circuit works with input supply of 30V DC and logic supply 5V DC. IC requires large size heat sink to work with full 10A current range. Screw terminals for input and output connections are provided. The OPA549 is a low-cost, high-voltage/high-current operational amplifier ideal for driving a wide variety of loads. This laser-trimmed monolithic integrated circuit provides excellent low-level signal accuracy and high output voltage and current. The OPA549 operates from either single or dual supplies for design flexibility. The input common-mode range extends below the negative supply. The OPA549 is internally protected against over-temperature conditions and current overloads. In addition, the OPA549 provides an accurate, user-selected current limit. Unlike other designs which use a “power” resistor in series with the output current path, the OPA549 senses the load indirectly. This allows the current limit to be adjusted from 0A to 10A with a resistor/potentiometer, or controlled digitally with a voltage-out or current-out Digital-to-Analog Converter (DAC). The Enable/Status (E/S) pin provides two functions. It can be monitored to determine if the device is in thermal shutdown, and it can be forced low to disable the output stage and effectively disconnect the load. The OPA549 is available in an 11-lead power package. Its copper tab allows easy mounting to a heat sink for excellent thermal performance. Operation is specified over the extended industrial temperature range, –40°C to +85°C.

This project is built for professional photo flash systems. The circuit generates high voltage from a low voltage battery to operate a photo-flash tube. The project can also be used in other applications like high voltage capacitor chargers, emergency strobe, high voltage power supply, security, detonators, etc. LT3751 is the heart of the project.

This is a high voltage regulator project that provides 5V regulated output with a load capacity of 50mA from input supply 10V to 60V. The project is based on the ZXTR1005K4 regulator which is fully integrated into a TO252 package. We have tested this project with 60V DC input, but the project can take higher voltage input up to 100V, please refer to the datasheet below for more info, and don’t forget to change the capacitor C1 with a higher voltage rating.

The project here is a 48V protected, high side switch designed to switch a 5A output load from input voltages from 8V to 48V. The circuit helps the user to easily ON/OFF the high current and voltage load with over-voltage lockout and over-current protection. The wide input range and low shutdown current (1μA typical) make it suitable for automotive, industrial, medical instruments, and telecom applications. This board offers a low 50ns (typical) propagation delay, fast switching times (<10ns), and 100% duty cycle operation. The project is based on LTC7000 which is a fast high voltage protected high side N-channel MOSFET driver. An internal charge pump fully enhances an external N-channel MOSFET switch, allowing it to remain on indefinitely. Its powerful gate driver can drive large gate capacitance MOSFETs with very short transition times, ideal for both high-frequency switching and static switch applications.

This is a fantastic project for makers, offering multiple output options of 3.3V, 5V, and 12V, with an input of 18-24V DC. This project is built around the MP2451 high-frequency (2Mhz) step-down switching regulator, ensuring efficient and reliable power conversion. For added convenience, a header connector is provided for outputs and input supply, while a power LED indicator ensures easy power status monitoring. This project is particularly well-suited for low-current applications, and its compact PCB design occupies a minimal footprint, making it ideal for space-constrained projects.